HOW TO glo™: STANDARD MODE VS BOOST MODE

With glo™ you are able to heat tobacco in an innovative way and can even control how fast you would like your tobacco stick to be heated thanks to the device’s two heating levels. Get to know all the differences as well as the advantages of both glo™ Standard and Boost mode.

glo™ HEATING LEVELS: CHOOSE YOUR MODE

To begin, it is important to note that your glo™ device is built to heat the neo™ sticks to up to 270 degrees Celsius. Heating up the tobacco stick at a certain temperature means there is no combustion process and allows you to enjoy real tobacco without smoke and ash. What’s more is that with glo™, there are two heating levels. You can choose to press either the glo™ Standard or Boost button, where both will take 3 seconds to be automatically activated. One important difference between the two modes is that activating the Boost button will allow the tobacco to heat up even faster.

	glo™ Standard Mode	glo™ Boost Mode
Activation period:	3 seconds	3 seconds
Vibration:	Once	Twice
Heating process:	20 seconds	15 seconds
Heating temperature:	Up to 250 degrees C	Up to 270 degrees C
Session duration:	4 minutes	3 minutes
Number of Puffs:	Unlimited	Unlimited

ACTIVATE THE DESIRED glo™ FUNCTION

HOW TO USE YOUR glo^TM HYPER X2 DEVICE?

1 Open the glo™ heater shutter door
2 Insert the neo™ stick
3 Turn on by pressing the control button

Depending on the mode you want to turn on:

- for Standard mode, press and hold Strandard button for 3 seconds.

- for Boost mode, press and hold the Boost button for 3 seconds.

The device will vibrate to indicate the session start.

The first light on the display will begin to flash as the start-up is initiated. The device will vibrate once when in standard mode, and twice when in boost mode.
4 The start-up procedure is completed when all lights on the outside of the display are illuminated (20 seconds for Standard mode and 15 seconds for Boost mode).

The next vibration means the neo™ stick has warmed up and you can start using it.
5 Place the neo™ stick to your lips and inhale gently, just like a regular cigarette. The lights will turn on to indicate session progress.When there is 10 seconds left of the session the device will vibrate and the LED display will pulse.

You may stop your session at any point by holding down any button for 3 seconds. The glo™ tobacco heater will gently vibrate to let you know it’s turning off.
6 After the session is over, the device will turn off automatically.

Remember that it is not possible to pause the session. The heated neo™ stick must be replaced with a new one to start a new session.
7 Remove the neo™ stick by pulling on the filter. Be careful - it may be hot.

NOTE: when using the device, leave the neo™ stick in the device.

HOW TO CLEAN YOUR glo^TM X2 DEVICE?

Before cleaning, leave the device to cool down at least 5 minutes.

It is recommended to clean it ever 20 sessions.

Warning: hitting or shaking the glo™ HYPER X2 tobacco heater to remove debris may damage it.

1 To clean the device, use the special brush included in the kit
2 Open the top and bottom flaps of the glo™ heater.
3 For best results, clean the machine from both sides.
4 If condensation forms at the opening on the bottom of the device, wipe it off with a tissue or cloth.

glo™ BOOST MODE: INCREASED TOBACCO ENJOYMENT

As mentioned above, in boost mode you can use your glo™ device much faster than if it was in standard mode. It takes only 15 seconds for your neo™ sticks to heat up after you insert it into your glo™ tobacco heater. With boost mode, your session will last about three minutes—shorter than in standard mode, but you will get a more intense consumption experience. In the end, both standard and boost mode enable an authentic tobacco enjoyment at a touch of a button—ready, set, glo™!